Solid-state battery testing presents a distinct set of mechanical challenges that liquid-electrolyte cells do not. Because solid electrolytes cannot flow or redistribute under pressure, the mechanical state of the cell stack becomes a direct determinant of ionic contact, interfacial resistance, and long-term stability. Force control, therefore, is not a peripheral concern in solid-state battery testing protocols — it is central to obtaining reproducible, physically meaningful results.
This article works through the topic systematically, from the fundamental role of stack pressure to the practical steps involved in designing a force-controlled testing protocol and interpreting the resulting data alongside electrochemical signals.
What makes force control critical in solid-state battery testing?
In solid-state cells, ionic transport across electrode-electrolyte interfaces depends on intimate physical contact between solid surfaces. Unlike liquid electrolytes, which conform to surface topography and maintain contact during volume changes, solid electrolytes require external mechanical force to sustain that contact throughout cycling.
When stack pressure is insufficient, interfacial voids form at electrode-electrolyte boundaries. These voids increase local ionic resistance and create current density non-uniformities that accelerate localised degradation. When pressure is excessive, brittle solid electrolytes — particularly oxide-based ceramics — can fracture, introducing electronic short-circuit pathways or mechanical failure modes that compromise the cell irreversibly.
Force control in solid-state battery testing is therefore a precision requirement. The applied load must be sufficient to maintain contact without inducing mechanical damage, and it must respond dynamically to the volume changes the cell undergoes during charge and discharge.
How stack pressure affects cell performance and degradation
Stack pressure influences solid-state cell behaviour through several coupled mechanisms. Understanding these individually helps explain why a single fixed pressure value is rarely adequate across a full experimental campaign.
- Interfacial contact resistance: Higher pressure generally reduces contact resistance at electrode-electrolyte interfaces by increasing the real contact area between surfaces with finite roughness.
- Li-metal anode morphology: In cells using lithium metal anodes, pressure suppresses void formation during stripping and promotes more uniform lithium deposition during plating, reducing the tendency toward dendrite nucleation at the interface.
- Electrolyte mechanical integrity: Sulphide-based solid electrolytes are relatively compliant and tolerate moderate pressure variation well. Oxide ceramics are brittle and respond to pressure non-uniformity with crack propagation, which can progress silently across cycles.
- Volume change accommodation: Electrode active materials expand and contract with lithiation state. In a constrained stack, these volume changes translate directly into pressure fluctuations unless the test cell provides active compensation.
For example, silicon-based anodes undergo volumetric expansion of roughly 300% on full lithiation. In a rigid fixture with no pressure regulation, this expansion drives stack pressure to levels that can fracture the electrolyte layer before the first cycle is complete. This illustrates why the choice of testing hardware is inseparable from the choice of electrode chemistry.
Limitations of static force approaches in legacy testing protocols
Previous-generation test cells typically applied force through a fixed mechanical arrangement — a set of bolts torqued to a defined value, or a spring stack pre-compressed to a nominal load. These static approaches were adequate for liquid-electrolyte cells, where the electrolyte could accommodate minor mechanical inconsistencies. In solid-state testing, they introduce systematic errors.
The core problem is that static fixtures cannot distinguish between the force applied at the start of a test and the force present during cycling. As the electrode stack expands and contracts, the actual load on the cell drifts away from the initial set point. In a rigid fixture, volume expansion raises pressure beyond the intended value. In a compliant spring arrangement, volume contraction reduces pressure below the threshold needed to maintain interfacial contact.
Conventional test cells also do not include a force sensor — only the initial pressure is read at assembly, and mechanical settling can reduce it over time without any indication that the load has changed. This means that the actual force experienced by the cell during cycling may differ substantially from the intended set point throughout the experiment.
A further limitation is reproducibility. Bolt-torque methods are sensitive to friction in the thread, surface condition, and operator technique. Two nominally identical cells assembled by different researchers may experience substantially different stack pressures, making inter-laboratory comparison difficult and obscuring real differences in material performance. Studies have cited an assembly failure rate of 43% for conventional test cells, with even experienced builders achieving only around 4 out of 5 working cells and inexperienced ones falling below 50%.
Conventional cells also compress electrode material inhomogeneously, and their plungers can embed particles during use, requiring grinding or polishing between measurements — a process that gradually alters cell geometry and further undermines reproducibility. Sealing typically relies on O-rings and PEEK housings; PEEK absorbs significant moisture and must be dried at 120°C under vacuum, adding preparation time and contamination risk.
How smarter force control systems work in modern test cells
Modern force test cells address the limitations of static approaches by integrating load measurement and, in more advanced configurations, active load regulation directly into the cell hardware.
Integrated load sensing
At a minimum, a force-controlled test cell incorporates a calibrated load cell or pressure sensor within the cell stack. This provides a continuous measurement of the actual force experienced by the electrodes and electrolyte, independent of what was set at assembly. The pressure signal can be logged alongside electrochemical data, giving researchers a complete picture of the mechanical state of the cell at every point in the experiment. The PAT-Cell-Force from EL-CELL includes an integrated force sensor for exactly this purpose. An optional gas pressure sensor can also be added, allowing force changes caused by gas evolution to be measured separately from purely mechanical ones — a distinction that is impossible to make with a single sensor or no sensor at all.
Active pressure regulation
More capable systems add a controlled actuator — typically pneumatic or motorised — that adjusts the applied force in response to the measured load. This allows the researcher to specify a target pressure and have the system maintain it within a defined tolerance throughout cycling, regardless of volume changes in the electrode stack. For solid-state cells with high-capacity anodes, this capability is not a convenience feature; it is a prerequisite for obtaining data that reflects material behaviour rather than mechanical artefacts.
Building on the contact resistance relationships described earlier, active pressure regulation also enables deliberate pressure variation protocols — for example, stepping through a range of stack pressures within a single experiment to map the pressure dependence of impedance or capacity.
Homogeneous compression and durable plungers
Beyond sensing and regulation, the mechanical design of the cell itself determines whether force is applied evenly across the electrode stack. The PAT-Cell-Force and PAT-Cell-Solid from EL-CELL both use the PAT-Solid-Core insert, which features guided plane-parallel tungsten carbide plungers and a dedicated pressing tool to ensure homogeneous compression. Tungsten carbide withstands high mechanical loads without embedding particles or degrading between measurements, eliminating the need for grinding or polishing and preserving cell geometry across experiments.
Sealing materials and moisture management
EL-CELL cells use aluminum seals and glass-metal feedthroughs instead of O-rings, and PPS plastic instead of PEEK. PPS absorbs significantly less moisture than PEEK, reducing contamination risk and cutting preparation time by removing the need for high-temperature vacuum drying. Together, these design choices — integrated force sensing, homogeneous compression, durable plungers, and low-moisture sealing — allow the PAT-Cell-Force and PAT-Cell-Solid to standardise and simplify preparation to the point where nearly every cell runs without assembly failure.
Designing a force-controlled testing protocol for solid-state cells
A well-designed force-controlled testing protocol specifies the mechanical boundary conditions as precisely as the electrochemical ones. The following steps provide a practical framework.
- Define the target pressure range: Identify the minimum pressure required to maintain interfacial contact for the specific electrolyte and electrode combination, and the maximum pressure the electrolyte can sustain without fracture. The operating protocol should keep the cell within this window at all times.
- Select the appropriate force mode: Decide whether constant-force or constant-displacement mode is more appropriate for the experiment. Constant-force mode maintains a set load and allows the stack to change thickness freely — useful for measuring volumetric strain. Constant-displacement mode fixes the stack thickness and measures the resulting force variation — useful for studying stress evolution.
- Set logging intervals for pressure data: Pressure should be recorded at the same time resolution as voltage and current. Pressure transients during charge and discharge carry diagnostic information that is lost if logging is too infrequent.
- Include a pre-cycling pressure stabilisation step: Before beginning electrochemical cycling, allow the cell to equilibrate under the target pressure for a defined period. This ensures that initial impedance measurements reflect a stable interfacial state rather than a transient assembly condition.
- Document assembly conditions fully: Record the initial stack thickness, the torque or actuator set point used during assembly, and the pressure reading at the start of measurement. This information is essential for reproducing the experiment and for comparing results across different cell builds.
Interpreting pressure data alongside electrochemical signals
Pressure data becomes most informative when analysed in conjunction with electrochemical signals such as voltage, current, and electrochemical impedance spectroscopy (EIS). The relationships between these signals reveal physical processes that neither dataset exposes alone.
During a galvanostatic charge cycle, a gradual increase in stack pressure typically reflects lithiation-driven expansion of the anode active material. A sudden pressure drop during charging, by contrast, may indicate delamination at the anode-electrolyte interface — a mechanical event that would also appear as an increase in the high-frequency real impedance measured by EIS. Correlating the two signals allows the researcher to assign a physical cause to the impedance feature with greater confidence than EIS data alone would permit.
Pressure hysteresis between charge and discharge — where the pressure at a given state of charge differs depending on the direction of cycling — can indicate irreversible microstructural changes in the electrode or electrolyte. This type of analysis is only possible when pressure is recorded continuously and synchronised with the electrochemical data stream.
A common misconception is that pressure data is useful only for detecting catastrophic mechanical failure. In practice, subtle pressure signatures during normal cycling carry quantitative information about interfacial contact evolution, creep in compliant electrolytes, and the onset of electrode particle fracture — all of which affect long-term cell performance before any obvious failure event occurs.
How EL-Cell GmbH supports solid-state battery testing with force control
EL-Cell GmbH designs test cells and supporting instrumentation specifically for the mechanical and electrochemical demands of solid-state battery research. Our product range addresses the requirements outlined in this article directly:
- The PAT-Cell-Force provides integrated force measurement and active pressure control within a standard coin-cell form factor, enabling continuous pressure logging synchronised with electrochemical data. An optional gas pressure sensor allows gas-evolution-driven force changes to be distinguished from mechanical ones.
- The PAT-Cell-Solid is designed for solid-state electrolyte chemistries, with a cell geometry that accommodates pellet-form electrolytes and applies well-defined uniaxial stack pressure. Both the PAT-Cell-Force and PAT-Cell-Solid use the PAT-Solid-Core insert with guided plane-parallel tungsten carbide plungers for homogeneous, reproducible compression.
- The PAT-Tester-i-16 integrates battery cycling, EIS, and environmental control in a single instrument, allowing pressure, impedance, and cycling data to be acquired on a common time base without additional synchronisation steps.
- Our ECD-4-nano electrochemical dilatometer measures electrode thickness changes with a resolution better than 5 nm, providing a complementary displacement measurement that can be run alongside force-controlled cycling experiments.
If you are developing or refining a solid-state testing protocol and would like to discuss which cell configuration and instrument combination fits your experimental requirements, contact our applications team directly through the EL-Cell website.



Comments are closed.